Industry

AISI 304 or 316? A Stainless Steel Selection Guide for Healthcare Facilities

26 August 2026

AISI 304 or 316? A Stainless Steel Selection Guide for Healthcare Facilities

The most common phrase in hospital equipment and laboratory furniture specifications is "stainless steel". Yet this phrase alone does not guarantee quality; stainless steel comes in dozens of grades, each with a different area of use.

The two grades most widely used in healthcare facilities are AISI 304 and AISI 316. Both belong to the austenitic stainless steel group, cannot be told apart by eye and are both sold as "stainless". Under certain conditions, however, the difference between them directly determines equipment life.

In this guide, we look at the technical difference between the two grades, which one is the right choice for which area, and why surface quality matters at least as much as the material.

The Key Difference: Molybdenum

AISI 304 is the most widely used stainless steel grade in industry, containing approximately 18% chromium and 8% nickel. The thin oxide layer that chromium forms on the surface protects the material against corrosion. When scratched, this layer renews itself on contact with oxygen — this is where stainless steel's "self-healing" property comes from.

AISI 316 adds molybdenum to this composition. Molybdenum significantly increases the resistance of the protective oxide layer to chloride ions.

In practice, this means that in the presence of chloride, 316 is far more durable than 304.

Why Does Chloride Matter?

Chloride is the main factor that damages the protective layer of stainless steel and causes pitting corrosion. Sources of chloride in healthcare facilities are more common than assumed:

  • Chlorine-based surface disinfectants
  • Cleaning solutions containing bleach
  • Mains water with high chloride content
  • Saline solution and body fluids
  • Salty air at coastal facilities

On surfaces in intensive and continuous contact with these substances, grade 304 may develop pitting stains and corrosion over time. Under the same conditions, 316 maintains its integrity for much longer.

Which Grade for Which Area?

Areas where AISI 304 is sufficient:

  • Patient room and corridor furniture
  • Nurse stations and station units
  • General storage cabinets and shelving systems
  • Worktops and preparation tables
  • Hand wash sinks and washroom equipment
  • Paper towel and soap dispensers

In these areas, 304 combined with the right surface finish provides many years of trouble-free service and is more cost-effective.

Areas where AISI 316 should be preferred:

  • Washing and disinfection zones in central sterilization units
  • Surfaces subject to intensive chlorine-based disinfection
  • Sections of laboratory worktops in contact with chemicals
  • Pathology and autopsy areas
  • Exterior and technical-area equipment at facilities near the coast

The question to ask when deciding is simple: Which chemical will this surface come into contact with, how often and for how long?

You can explore our stainless steel solutions in our Hospital Equipment and Washroom Equipment categories.

As Important as the Material: Surface Quality

The second factor, often overlooked in specifications but decisive for hygiene, is surface finish.

The rougher a stainless steel surface is, the more organic residue and microorganisms cling to its microscopic pores. A rough surface is more prone to biofilm formation despite regular cleaning.

For this reason, surface roughness in healthcare equipment is a criterion that deserves as much attention as material grade. A well-finished, smooth and non-porous surface makes cleaning easier and increases the effectiveness of disinfectants.

Likewise, the finishing quality of weld seams is critical. A poorly ground weld area becomes the first point where corrosion starts.

Thickness and Structural Strength

Even if the material grade is chosen correctly, equipment cannot complete its service life if the sheet thickness is insufficient. On heavily used worktops and door surfaces, thin sheet bends and deforms over time.

When preparing a specification, not only the grade but also the thickness value should be stated. The phrase "AISI 304 stainless steel" alone is not enough; thickness, surface finish and welding standard should also be defined.

Long-Term Cost Comparison

AISI 316 costs more than 304. For this reason, equipping an entire facility with 316 is not an economical approach.

The right approach is to evaluate the facility zone by zone: using 316 in the limited number of areas with high chloride exposure and 304 elsewhere both protects the budget and ensures the right performance in every zone.

The cost of using 304 in the wrong zone is not only equipment replacement; in a healthcare facility, replacing equipment means taking that area temporarily out of service.

Decision Checklist

Get clear answers to these five questions when selecting equipment:

  1. Is the material grade documented? (AISI 304 / 316)
  2. Is the sheet thickness defined in the specification?
  3. Are the surface finish and roughness value stated?
  4. Are the weld areas finished and passivated?
  5. Has the type of disinfectant to be used been shared with the manufacturer?

A supplier who can answer all five of these questions can also guide material selection correctly.

The Right Material for the Right Area

Choosing stainless steel is not a "good–bad" choice but a suitability decision. Just as not every area requires 316, proceeding with 304 in zones with a high chloride load creates costs in the long run.

At Paloma, we evaluate the conditions of each area during the project design stage and determine the appropriate material grade for every zone.